HomeProdukteMultifunctional Gate Box MGBMGB-APMGBS-P-L1-AP-U-R-AZE-SAA-176258

MGBS-P-L1-AP-U-R-AZE-SAA-176258 (Order no. 176258)

Bus module MGB-B...-PN... with 3 controls/indicators, push-pull plug, Test Neuer

1 illuminated pushbuttons
1 signal indicator
1 operating mode selector
including adhesive labels
Pre-assembled on mounting plates
Integrated Profinet RT switch
Push-pull plug
Test New
next test approved?
next test two approved?
next test three approved?
last test?

MGBS-P-L1-AP-U-R-AZE-SAA-176258 (Order no. 176258)

Description

Profinet connection

Connection via push-pull plugs according to IEC 61076-3-117

Profinet RT switch

Point-to-point topology network structure due to integrated RT switch.

TEST Typical operating distances

With actuators CES-A-BBA and CES-A-BCA

For a side approach direction for the actuator and safety switch, a minimum distance of s = 4 mm must be maintained so that the actuating range of the side lobes is not entered.

With actuator CES-A-BPA

For a side approach direction for the actuator and safety switch, a minimum distance of s = 6 mm must be maintained so that the actuating range of the side lobes is not entered.

Attention:

The actuating range may vary depending on the actuator, substrate material and installation situation. Further actuating ranges can be found in the operating instructions.

Dimensional drawings

Technical data

Approvals

TUEV Süd München_Z10 040393 0033 Rev. 01

Operating and display elements

Occupancy diagram	B2

Occupancy diagram

Item	Color	Slide-in label	Version	Switching element
11	red		Signal indicator
12	white		Illuminated pushbutton	1NO
13		Entsichert / Unsecured ; Sonderfunktion / Special function ; Gesichert Zentral / Secured Central	Operating mode selector	Code 2 of 3

Electrical connection values

Connecting cable
Ethernet	Profinet I/O cable, at least cat. 5e
Rated insulation voltage U_i	75 V
Rated impulse voltage U_imp	0.5 kV
EMC protection requirements	In accordance with EN 61000-4 and EN 61326-3-1
maximum feed-in current in the connection block
X1, X2	max. 4000 mA
Safety class	III
Current consumption	max. 500 mA
Degree of contamination (external, according to EN 60947-1)	3
	Power supply X1
Fuse
external	min. 1 A slow blow
Operating voltage DC
L1	24 V DC -15% ... +10% ((reverse polarity protected, regulated, residual ripple<5%, PELV))
Auxiliary voltage DC
L2	24 V DC -15% ... +10% (The auxiliary voltage is not required for the MGB system)
	Power supply X2
Operating voltage DC
L1	24 V DC -15% ... +10% (For looping through for connected devices)
Auxiliary voltage DC
L2	24 V DC -15% ... +10% (For looping through for connected devices)

Mechanical values and environment

Connection type
	Push-pull power (X2 (The document PROFINET 'Cabling and Interconnection Technology' from the PNO aids in the correct selection of cables.))
according to IEC 61076-3-117, variant 14, screened, Profinet I/O cable, at least cat. 5e	Push-pull RJ45 (X4 (The document PROFINET 'Cabling and Interconnection Technology' from the PNO aids in the correct selection of cables.))
	Push-pull power (X1 (The document PROFINET 'Cabling and Interconnection Technology' from the PNO aids in the correct selection of cables.))
according to IEC 61076-3-117, variant 14, screened, Profinet I/O cable, at least cat. 5e	Push-pull RJ45 (X3 (The document PROFINET 'Cabling and Interconnection Technology' from the PNO aids in the correct selection of cables.))
Installation orientation	any
Storage temperature	-25 ... 70 °C
Response time
Operating mode selector	max. 220 ms Turn-off time (The reaction time is the max. time between the change in the input status and the deletion of the corresponding bit in the bus protocol.)
Shock and vibration resistance	Acc. to EN IEC 60947-5-3
Degree of protection	IP54
Ambient temperature
at U_B = 24 V DC	-20 ... 55 °C
Material
Housing	Fiber glass reinforced plastic, nickel-plated die-cast zinc, stainless steel